$49 40W CO2 Laser Power Supply for CO2 Laser Engraver Cutter MYJG, 1 Arts, Crafts Sewing Crafting Craft Supplies 2021 40W CO2 Laser Power Supply Cutter MYJG Engraver 1 for 2021 40W CO2 Laser Power Supply Cutter MYJG Engraver 1 for Supply,CO2,40W,www.gaganpalacenj.com,$49,Laser,1,Laser,Power,MYJG,,Arts, Crafts Sewing , Crafting , Craft Supplies,for,Engraver,CO2,Cutter,/arar755545.html $49 40W CO2 Laser Power Supply for CO2 Laser Engraver Cutter MYJG, 1 Arts, Crafts Sewing Crafting Craft Supplies Supply,CO2,40W,www.gaganpalacenj.com,$49,Laser,1,Laser,Power,MYJG,,Arts, Crafts Sewing , Crafting , Craft Supplies,for,Engraver,CO2,Cutter,/arar755545.html

2021 40W CO2 Laser Power Supply Max 62% OFF Cutter MYJG Engraver 1 for

40W CO2 Laser Power Supply for CO2 Laser Engraver Cutter MYJG, 1

$49

40W CO2 Laser Power Supply for CO2 Laser Engraver Cutter MYJG, 1

|||

Product description

--Application: Engraving, seal-cutting, etc.
--Protection switch: test the external water, ventilation, etc., to protect laser device
--TTL voltage level control: can be set high or low lever
--Easy control: the start and stop of laser can be easily controlled by TTL level.
--New function: timely scene judging which part is damaged, laser tube or laser power.
--High Security: input and output of power supply are separated completely to avoid getting an electric shock.
--Open circuit protection: with well-grounded enclosure, the power supply can work in open-circuit for a short time,
which could avoid the damage of laser power supply because of the bursting of laser tube, thereby enhancing the life of power supply.


Pin Definition:

*P1:
1--L-: Connect Negative Electrode of Laser Tube.
2--FG: Connect with G Internal, and Connect the Power Supply Shell.
3amp;4--AC AC: AC 110V/220V Input.

*P2:
1--G Signal Ground:The foot must connected with laser machine's enclosure and ground properly.
2--P Input Signal:Water Protction Switch.
3--L Input Signal:The control of laser: Low Level, emitting laser.
4--G Signal Ground : The foot must connected with laser machine's enclosure and ground properly.
5--IN Input Signal :Laser Power supply control terminal can use 0-5V Analog Signal Control,also can use 5V PWM Signal to Control.
6--Output Power: 5V,Max output Current 50mA.

*P3:
1--24V:output 24V,Max Current 2A,power for master board.
2--G:24V and 5V Ground.
3--5V:output 24V,Max Current 1A.
4--L:The control of laser: Low Level, emitting laser.

Note: the standard laser power supply is with 220V, if you need 110V, you can do adjust the Voltage switch of the side.

40W CO2 Laser Power Supply for CO2 Laser Engraver Cutter MYJG, 1


You like tumblr ? tumbex is your access to all blogs, with a streamlined design and optimized navigation


Explore a tumblog :

.tumblr.com

About

Tumbex indexes only tumblr posts which have caption or tags. We analyse the content and define if tumblr or posts are nsfw/adult.

If your tumblr was detected as nsfw by mistake, you can request a review and we will manually check your tumblr.

Content Removal

If you want to remove any content, just report them with the report button : .

If the content is related to violence against minors, it will be immediately removed from tumbex and we will report it to tumblr.com.

For reports of copyright infringement / invasion of privacy, please provide proof by email that this is your property. We will then delete the contents of tumbex.
Unfortunately, we are not affiliated with Tumblr and do not have the ability to remove images hosted directly by Tumblr.
You can however go to https://www.tumblr.com/abuse and follow the procedure for deleting content.

The post link will be requested, you can find it at the bottom of each page by following the link "Original Post".